ASTM A635 PDF

This standard is issued under the fixed designation A /A M; the 1 This specification is under the jurisdiction of ASTM Committee A ASTM A/AM: Standard Specification for Steel, Sheet and Strip, Heavy- Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural. Find the most up-to-date version of ASTM A at Engineering

Author: Gajora Grobar
Country: Croatia
Language: English (Spanish)
Genre: Politics
Published (Last): 21 January 2016
Pages: 224
PDF File Size: 13.7 Mb
ePub File Size: 8.90 Mb
ISBN: 824-5-98761-955-3
Downloads: 34056
Price: Free* [*Free Regsitration Required]
Uploader: Yozshull

AK Steel ASTM A and A Hot Rolled Carbon Steel, Structural Steel (SS)

If either coarse or? Depending upon the angle of the bevelled edge cut, the width of the narrow surface of the cut-edge coil may be less than the minimum ordered width.

Your comments a65 receive careful consideration at a meeting of the responsible technical committee, which you may attend. For nominal thickness, the tolerance is divided equally over and under. However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. The ability of manufacturers to meet the maximum coil weights depends upon individual mill equipment.

ASTM A635 Grade 1018

All Widths A All Widths. The tolerances provided in the table z635 based on minimum thickness tolerance over, no tolerance under. Click here to view all the property values for this datasheet as they were originally entered into MatWeb. Asgm contents, results, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC.

  CAGE BACCHANALE PDF

Combining values from the two systems may result in non-conformance with the standard. Over 8 to 12, incl Speci? Approved March 1, Over 8 to 12, incl Crown Tolerances for W635 In the event that the manufacturer is dissatis? These tolerances do not include crown, and, therefore, the tolerances given in Table A1.

Please contact us at webmaster matweb. Hot-rolled heavy thickness coils 12 in.

We appreciate your input. Current edition approved Sept. NOTE 3—This table was constructed by multiplying the values in the standard table astmm 0. No Tolerance Under 7 16 12 9 16? Cast or heat analysis shall be made to determine the conformance with the requirements.

These tolerances do not include crown, and, therefore, xstm tolerance given in Table A1. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

We also ask that you refer to MatWeb’s terms of use regarding this information. The term weight is used when inch-pound units are the standard. Specimen preparation and asstm methods are discussed. NOTE 1—Heavy-thickness edge cutting results in a bevelled edge. Carbon Manganese to 0. These coils are normally produced from rimmed, capped, or semi-killed steel.

The manufacturer must be consulted regarding the capability to control bevel angle. Index of Tables, Dimensions, and Allowances 4.

NOTE 2—Micrometers used for measurement of thickness shall be constructed with anvils and spindles having minimum diameters of 0. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The width shall be measured on the wide surface of the cut-edge coil. B The tolerances provided in the table are based on minimum thickness tolerance over, no tolerance under. Pickled or blastcleaned material has cut edges; if mill-edge material is required, it must be speci?

  ELKAY LR2219 PDF

The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values.

Conformance to Annex A1 is mandatory when the “M” specification is used. Hot roll manufacturer de? However, the document shall clearly identify the organization submitting the document. Note asym term asttm is used when inch-pound units are the standard.

The manufacturer shall be noti?

Over Over Over Over Over Over Over Over Over Over Over Over Over Over 12 14 17 19 21 24 26 28 35 50 60 65 70 80 to to to to to to to to to to to to 6a35 14, 17, 19, 21, 24, 26, 28, 35, 50, 60, 65, 70, 80, incl incl incl incl incl incl incl incl incl incl incl incl incl Tolerance Over Speci?