Standard Specification for Polypropylene and Extrusion Materials. ASTM D To request a quote for this test or others. Click Here. Buy ASTM D CLASSIFICATION SYSTEM AND BASIS FOR SPECIFICATION FOR POLYPROPYLENE INJECTION AND. Designation: D – Standard Specification for. Polypropylene Injection and Extrusion Materials1 This standard is issued under the fixed designation D.
|Published (Last):||17 September 2018|
|PDF File Size:||17.72 Mb|
|ePub File Size:||13.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
Exceptional tensile strength and stiffness lends this material to almost any fabrication.
It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Standards can be obtained from appropriate standards authorities. This specification covers polypropylene materials, suitable for injection molding and extrusion, that include unreinforced polypropylene with natural color only, unfilled and unreinforced polypropylene, calcium carbonate filled polypropylene, glass reinforced polypropylene, polypropylene copolymers, and talc filled polypropylene. Superior chemical and heat resistance that allows continual operating temperatures up to ‘F.
Certain processes, such as adhesion and FRP reinforcement can significantly reduce the permissible temperature limits. Increased impact resistance over homopolymer polyproplene down to 0’F. Link to Active This link will always route to the current Active version of the standard. No other units of measurement are included in this standard. See individual methods for more information. This specification defines pertinent properties, test methods, parameters and sample preparation for the evaluation of polypropylene for molding and extrusion.
Historical Version s – view previous versions of standard Translated Version s: Polymers consist of homopolymer, copolymers, and elastomer compounded with or without the asgm of impact modifiers ethylene-propylene rubber, polyisobutylene rubber, and butyl rubbercolorants, stabilizers, lubricants, or reinforcements.
Excellent chemical resistance to a broad range of acids, alkalis and most organic solvents up to ‘F. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Excellent chemical resistance to both acid and alkai solutions for temperatures up to maximum of ‘F. Due to copyright restrictions, we are not able to provide copies of standards. Co-Polymer Polypropylene High-impact grade material which involves the additional copolymerization of propylene zstm ethylene in a secondary reactor.
Plastic Testing Leader-Elastomers-Composites-Polymer testing PTLI
Extruded, stress free, consistently flat material. Individual methods outline specific guidelines as to time to test after molding. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
D Test Method for Satm Light grey standard with additional colors available upon request. Controlled laboratory atmosphere is required. This abstract is a brief summary of the referenced standard.
Tests shall be conducted on each of the specimens to determine the asttm physical and mechanical properties of the materials. Standard Specification for Polypropylene and Extrusion Materials. To request a quote for this test or others Click Here.
Excellent chemical resistance, frictional resistance, and strength up to ‘F. Polymers consist of homopolymer, copolymers, and elastomer compounded with or without the addition of impact modifiers, for example, ethylene-propylene rubber, polyisobutylene rubber, and butyl rubber, colorants, stabilizers, lubricants, or reinforcements.
It is the responsibility of atm supplier and the buyer of recycled, reconstituted, and reground materials to ensure compliance. ASTM does not give any warranty express or implied or make any representation that the contents d4011 this abstract are accurate, complete or up to date. Injection molding of test specimens is required for all tests outlined except heat stability testing. All grades are self-extinguishing.
ASTM D4101 – 17
This standard does not purport to address all of the safety concerns, if any, associated with its use. Please call for more information v4101 these special materials. Typically, different materials have unique requirements related to the generation of the specific properties. High impact properties of this material give it superior structural integrity over Type I PVC in larger industrial applications.
This polymer offers extremely low permeability to liquids, gases, and vapors. If other axtm are necessary to identify particular characteristics important to specific applications, these shall be designated by using the suffixes given in Section 1. Specimen Preparation is based on classification of basic composition.
Standard Specification for Polypropylene and Extrusion Materials
Ideal material for tank construction. Additional test methods are also called out. ECTFE has excellent chemical and mechanical properties, impact strength, and a broad service use temperature. The properties included in this classification system are those required to identify the compositions covered.